Small Tft Module manufacturers

3.2TFT LCD module
3.2 TFT LCD module XTPT32NN01-01
Model No. XTPT32NN01-01
►Display Format : 240×320
►Size: 3.2″
►View Direction: 12H
►Interface: MCU
►Built-in Controller: ILI9341V
►Touch Screen : NA
General Description of 3.2 TFT LCD module XTPT32NN01-01
3.2 TFT LCD module XTPT32NN01-01 is a TM (Transmissive) type color active matrix TFT (Thin Film Transistor) liquid crystal display (LCD) that uses amorphous silicon TFT as a switching device. This 3.2 TFT LCD module XTPT32NN01-01 is composed of a TFT-LCD module, a driver circuit and a back-light unit . The resolution of a 3.2″ contains 240RGBx320 dots and can display up to 262k colors. The following table described the features of XTPT32NN01-01.
Features
1.1 LCD Module
ItemSpecificationUnit
Screen Size3.2inchesDiagonal
Display Resolution240 x RGB x 320Dot
Dot Pitch0.2025 (H) x 0.2025 (V)mm
Active Area48.6 (H) x 64.8 (V)mm
Outline Dimension56.64 (W) x 79.3 (H) x 2.45(D)mm
Display ModeNormally white/Transmissive–
Pixel ArrangementRGB-Stripe–
Surface TreatmentAnti-glare (AG)–
Display Color262K–
Optima View Direction12 o’clock–
Input InterfaceMCU SPI/16-bits /8-bits/RGB–
Color GamutNTSC 60%–
Drive ICILI9341–
2.Mechanical Information
ItemMin.Typ.Max.UnitNote
Module SizeHorizontal (H)–56.64–mm–
Vertical (V)–79.3–mm(1)
Thickness (T)–2.45–mm(2)
Weight–N/A–g–
Note (1) Not include FPC.
Refer to the Outline Dimension for further information.
(2) Back-light unit are included.
3. Electrical Specifications
3.1 Absolute Max. Ratings
3.1.1 Absolute Ratings of Environment
If the operating condition exceeds the following absolute maximum ratings, the TFT LCD module may be damaged permanently.
(Ta=25±2°C, VSS=GND=0)
ItemSymbolMin.Max.UnitNote
Storage temperatureTSTG-3080°C(1)
Operating temperatureTOPR-2070°C(1,2,3)
Note (1) 95 % RH Max. ( 40 °C ≥ Ta ). Maximum wet-bulb temperature at 39 °C or less. (Ta > 40 °C) No condensation.
Note (2) In case of below 0°, the response time of liquid crystal (LC) becomes slower and the color of panel becomes darker than normal one. Level of retardation depends on temperature, because of LC’s character
Note (3) Only operation is guarantied at operating temperature. Contrast, response time, another display quality are evaluated at +25°C.
3.2 Electrical Absolute Rating
3.2.1 TFT-LCD Module
(Voltage Referenced to VSS)
ItemSymbolValueUnitCondition
Min.Max.
Digital Power Supply VoltageVDDVSS-0.35.0V–
3.2.2 Back-Light Unit
(Ta=25±2°C)
ItemSymbolMin.Max.UnitNote
Forward currentIf–60mA(1)
Reverse voltageVR–5.0V(1)
Note (1) Permanent damage to the device may occur if maximum values are exceeded or reverse voltage is loaded. Functional operation should be restricted to the conditions described under normal operating conditions.
4.Electrical Characteristics
4.1 TFT-LCD Module (DC Characteristics)
ItemSymbolValueUnitNote
Min.Typ.Max.
Power Supply VoltageVDD2.53.13.3V
Input High Threshold VoltageVIH0.7 VDD-VDDV
Input Low Threshold VoltageVIL0-0.3 VDDV
Power Supply CurrentICC-(20)(25)mA(1)
Power ConsumptionPL-(66)(90)mW(1)
Note (1) The specified power consumption is under the conditions at VDD=3.3V , FV=60Hz, whereas a Power dissipation check pattern below is displayed.
Black Pattern / 0 Gray
Active Area
4.2 Backlight Unit
The back-light system is an edge-lighting type with five white LEDs (Light Emitting Diode).
(Ta=25±2°C)
ItemSymbolValueUnitCondition
Min.Typ.Max.
LED VoltageVF2.73.13.5V
LED CurrentIF-100-mA
Power ConsumptionPBL-310-mW
Note (1) Where  PBL = VF × IF
5 Input Terminal Pin Assignment
5.1 Pin Assignment
 
Pin
 No.
Symbol
Description
1XLThe TP Signal
2YUThe TP Signal
3XRThe TP Signal
4YDThe TP Signal
5GNDPower Ground
6IOVCCPower supply
7VCIPower supply
8FMARKTearing effect out pin synchronize MPU to frame writng
9CS/SPI CS
10DC/SPI SCLCommand/data selection selection in parallel
11WR/SPI DCWrite enable pin in parallel
Serial data clock in serial bus system
12RDRead enable pin
13SPI SDI/SDASerial data input signal
14SPI SDOSerial data output signal
15RESETSystem Reset
16GNDPower Ground
17-32DB0-DB15Data Input/Output
33AB/L Anode
34-36K-KB/L Cathode
37GNDPower Ground
38IM0Select interface mode
39IM1
40IM2
(Ta=25±2°C)
ItemSymbolConditionMinTypeMaxUnitNote
Brightness–q=0° Normal Viewing Angle–350–cd/m2–
Response timeTR–1520ms–
TF–3550ms
Contrast ratioCR400500——
Color Chromaticity
(CIE1931)RedRX0.6060.6260.646—-
RY0.3140.3340.354
GreenGX0.2570.2770.297–
GY0.5290.5490.569
BlueBX0.1220.1420.162–
BY0.1020.1220.142
WhiteWx0.2830.3030.323–
Wy0.3050.3250.345
Viewing Angle (12H)Hor.qRCR³103545–Degree–
qL3545–
Ver.fH3545–
fL1020–
6.Optical Characteristics
The following items are measured under stable conditions. The optical characteristics should be measured in a dark room or equivalent state with the methods shown in Note (1).
Measuring equipment: BM-5A, BM-7,
(Ta=25±2°C)
ItemSymbolConditionMinTypeMaxUnitNote
Brightness–q=0° Normal Viewing Angle–350–cd/m2–
Response timeTR–1520ms–
TF–3550ms
Contrast ratioCR400500——
Color Chromaticity
(CIE1931)RedRX0.6060.6260.646—-
RY0.3140.3340.354
GreenGX0.2570.2770.297–
GY0.5290.5490.569
BlueBX0.1220.1420.162–
BY0.1020.1220.142
WhiteWx0.2830.3030.323–
Wy0.3050.3250.345
Viewing Angle (12H)Hor.qRCR³103545–Degree–
qL3545–
Ver.fH3545–
fL1020–
a.Test equipment setup
After stabilizing and leaving the panel alone shall be warmed up for the stable operation of LCM, the measurement should be executed. Measurement should be executed in a stable, windless, and dark room. Optical specifications are measured by Topcon BM-7(fast) with a viewing angle of 2 at a distance of 50cm and normal direction.
b.Definition of response time: Tr and Tf
The response time is defined as the following figure and shall be measured by switching the input signal for “black” and “white”.
c.Definition of contrast ratio:
d.Measured at the center area of the panel when all the input terminals of LCD panel are electrically opened.
e.View Angle
f.Definition of Luminance of White: Luminance of white at the center points
Light Source of Back-Light UnitLED Type
g.Definition of White Uniformity
h.The definition of Color Gamut -Color Chromaticity CIE 1931
Color coordinate of white & red, green, blue at center point.
Color Gamut : NTSC(%) = ( RGB Triangle Area / NTSC Triangle Area ) x 100
7. Interface Timing
8.Reliability Condition for LCD
No change on display and in operation under the following test condition.
Condition: Unless otherwise specified, tests will be conducted under the following condition.
Temperature: 205C          Humidity: 655%RH
Tests will be not conducted under functioning state.
No.ParameterConditionNotes
1High Temperature Operating60°C±2°C, 240hrs (Operation state)–
2Low Temperature Operating-10°C±2°C, 240hrs (Operation state)–
3High Temperature Storage70°C±2°C, 240hrs–
4Low Temperature Storage-20°C±2°C, 240hrs–
5High Temperature and High
Humidity Operation Test60°C±2°C, 90%, 240hrs–
6Vibration TestTotal fixed amplitude: 1.5mm
Vibration Frequency: 10~55Hz
One cycle 60 seconds to 3 direction of X, Y,
Z each 15 minutes.–
7.Drop TestTo be measured after dropping from 60cm high
on the concrete surface in packing state.
—
Notes:  
1. No dew condensation to be observed.
2. The function test shall be conducted after 4 hours storage at the normal temperature and humidity after removed from the test chamber.
3. Vibration test will be conducted to the product itself without putting I in a container.
9.Dimensional outlines
FAQ
1.What does TFT screen mean?
Short for thin film transistor, a type of LCD flat-panel display screen, in which each pixel is controlled by from one to four transistors. The TFT technology provides the best resolution of all the flat-panel techniques, but it is also the most expensive. TFT screens are sometimes called active-matrix LCDs.
2.What is a TFT screen used for ?
thin film transistor liquid crystal display (TFT-LCD) is a technology which is used in LCD monitor and television displays. TFT technology can be used to give one of the clearest pictures of any flat screen display and it uses much less electricity than older screens.
3.Which is better TFT or LED?
A TFT means ThinFilmTransistor which may refer to an ordinry LCD screen. Both the TFT and LED displays are made of LCD, but the difference only comes in the backlightig. LCD/TFT uses CCFL(cool compound fluroscent lamp) while the other uses LED to backlight. … But perfomancewise LEDs are far better than TFT displays.
4.What is TFT color?
A thin-film-transistor liquid-crystal display (TFT LCD) is a variant of a liquid-crystal display (LCD) that uses thin-film-transistor (TFT) technology to improve image qualities such as addressability and contrast.Small Tft Module manufacturers
website:http://www.amotec-lcd.com/tft-module/small-tft-module/